See FISITA Library items from Nico Langhof




Mr. Felix Wich, University of Bayreuth, GERMANY, Dr. Nico Langhof, University of Bayreuth, GERMANY, Prof. Dr.-Ing. Walter Krenkel, University of Bayreuth, GERMANY

The formation of a stable 3rd-body, independence of the applied sliding speeds and braking pressures, is considered to be crucial for low wear rates and a desired coefficient of friction that can be measured between the regarding friction materials. Therefore, e.g. LowMet pads and grey cast iron discs are a very suitable friction couple. However, there are some drawbacks of both materials. Their thermomechanical stability is limited, they tend to be corroded very quickly and harmful fine dust emission during braking and acceleration causes enormous challenges for future applications, like in electric cars.

One approach that can help to overcome these challenges are ceramic friction materials. The well established ceramic brake disc for passenger cars, has a temperature stability up to 1300 °C, a low density of about 2.4 g/cm3, shows no corrosion and as a life time disc (> 300.000 km) very low wear rates, i.e. significantly less fine dust particle emission. Some alternative approaches still propagating grey cast iron discs, that are coated with different ceramic materials in order to decrease the fine dust particle emission.

However, on the opposite side, the brake pad is still mainly unchanged, metal containing and prone for corrosion. Due to this behavior, in case of an emergency brake event, the maximum COF is reached much slower, compared to a non corroded brake pad surface.

Therefore, novel corrosion resistant (ceramic) brake pads are required as counterparts for those novel developed brake discs.

Within this work different ceramic pads are studied, based on C-fiber reinforced SiC. Previous tribological tests show the promising frictional behavior in terms of low wear rates and very high COFs. However, the COF is strongly depended on speed and pressure. Due to adhesive friction, especially at low speeds [removed] 0.9, partially vibrations occurs, which make such pads nearly impossible to adapt within braking system of a car.

In order to overcome this drawback different graphite additives were selected as modifying phases within the ceramic pads. The goal was to form a suitable 3rd-body that decreases the COF at low speed < 10 m/s and minimize the COF difference between high (20 m/s) and low speed (< 10 m/s).

The brake pads were manufactured by mixing 3k-C-fibers (6 mm lengths) with phenolic resin and three different types of graphite. All graphites differ in terms of particle shape, particle sizes and size distribution. The mixtures were warm-pressed, cross-linked at about 170 °C and subsequently pyrolyzed > 900 °C under inert conditions. This thermal treatment causes the transformation of the matrix resin into an open porous amorphous carbon. During the final step, liquid silicon was infiltrated (>1420 °C, vacuum) within the open pores in order to enable the reaction of silicon with the amorphous carbon matrix to SiC.

All manufactured brake pads were studied in term of their bulk density, open porosity and microstructure, including some thermomechanical properties, e.g. the compressive strength and thermal conductivity.

Afterwards, for each of the three qualities, a reference without graphite and LowMet, 30x30 mm2 pads with 10 mm thickness were prepared and tested on a fly wheel dynamometer (about 100 kgm2) with a starting speed of 20 m/s and a braking pressure of 3 MPa. As a counterpart the commercial available internal ventilated C/SiC ceramic brake disc from BremoSGL was selected (about 410 mm ∅). The COF, the wear rates and the temperature of the braking parings were determined.

The effect of adding 15 wt.-% graphite is visible for every type of the studied brake pads compared to the pads without additives. Extremely high COFs at low speeds can be prevented and due to the selection of suitable particles sizes and graphite amounts, the COF at low speeds was decreased significantly (< 0.7). In order to understand this favorable behavior the frictional surfaces of the pads were studied after braking. The results show, that due to the addition of graphite the dependence of the COF on speed could be reduced significantly and the wear rate is very low as well. In contrast to the C/SiC pads without graphite, notable areas could be detected in scanning electron microscopy, where a 3rd-body can be confirmed. This 3rd-body is presumably responsible for the significantly improved tribological performance of the pure ceramic friction couple.

The very promising frictional properties of these tailored C/SiC ceramic brakes pads, show the possibility to compete with the current conventional brake pads and to overcome the future challenges accompanying with the electric driven vehicles as well.

EuroBrake 2021






Dipl.-Ing. Thorsten Opel (né Balzer), University of Bayreuth, GERMANY

Dr. Nico Langhof, University of Bayreuth, GERMANY

Prof. Dr.-Ing. Walter Krenkel, University of Bayreuth, GERMANY

Future mobility concepts like electric powered vehicles demand for new braking technologies and brake disc concepts. Due to the technological progress regarding the recuperation capabilities of electric vehicles, friction brakes are merely needed for complementary braking and more importantly for emergency braking manoeuvers. Consequently, new brake disc designs are viable in which for example the mass of the brake discs can be reduced. Due to the fact, that the brake discs in electric powered vehicles aren’t used as frequently, the corrosion of the brake discs and brake pads are problems which have to be coped with. Thusly the use case or rather the (performance) requirements for brake discs for electric powered vehicles are very different compared to brake discs for cars with internal combustion engines.

A new concept in the form of a metal-ceramic hybrid brake disc is propagated for the use in electric powered vehicles. It consists of an aluminium carrier body which is lined with ceramic friction segments on the friction surface of both sides. For the friction segments a short fibre reinforced ceramic matrix composite (in particular a carbon fibre reinforced silicon carbide: C/SiC) is used. The outlined concept allows for a light-weight, corrosion resistant and economically viable emergency brake with outstanding friction properties for the use in electric powered vehicles. An overview is given on the potential application areas and on the design, construction, manufacturing and testing of said hybrid brake disc.

A potential use case of a mid-class sedan with a mass of around 1.8 t and maximum travelling speeds of up to 200 km/h is taken as a basis for the design and construction of a metal-ceramic hybrid brake disc prototype. This prototype was tested on the dynamometer test bench at the University of Bayreuth under emergency braking conditions. Different characteristic values like wear, coefficient of friction and different temperatures were measured. The results are compared to results of standard commercially available brake discs (e. g. cast iron and carbon ceramic brake discs). Furthermore, possible joining methods were evaluated and thermomechanical characterisations of different joints were conducted.

EuroBrake 2021




Error message goes here.


Person profile goes here.


Team Leader Ceramic Matrix Composites

Company Text

Job title

Company Name

Company Text

Dr. Nico Langhof

FISITA Committees & Groups

Executive Board

News on FISITA Spotlight

16 July 2021

Spotlight title

Stay up to date with FISITA Spotlight

More Blogs Item Title

Excerpt from the blog goes here - this will give the reader a brief snapshot of what the post is about...

16 July 2021